Accessories

March Rifle Scopes can be ordered with extra three inch or 75mm (3 inch) long sunshades. These all-metal shades reduce stray light as well as decreasing barrel flare and ghosting off the target.

DB485-0for 24mm objective models

2-DB179-0for 42mm objective models

2-DB115-0/-Sfor 52mm objective models
(“-S” is for Silver models)

2-DB256-0/-Sfor 56mm objective models
(“-S” is for Silver models)

2-DB256-G (Dark grey)for 56mm objective of 8-80×56 Majesta model

*Please be aware that a gray sunshade may be slightly different in color tone from your scope as even if the same color code is used and plated in the same factory, minute variations in color tone (brightness (lightness/darkness of color) and shade) can occur due to the manufacturing process.

Anti reflective device (ARD)

DB391-A24mm objective models

DB391-B42mm objective models

DB391-C52mm objective models

DB391-D56mm objective models

MD Disk help to reduce the amount of light coming into a scope by up to 50%, depending on the conditions. This light reduction increases the scopes depth of field and, prehaps more impotantly for competition shooters, reduces the amount of seen mirage. Using a MD Disk at 60 or 80 power gives you a competitive advantage when the conditions turn bad and lets you see the target better than your competitor.
Weight : 0.25 oz (7.1 g)

DB269-0For 56mm objective models
With MD disk attached,the inner diameter will be 43mm

DB062-0For 52mm objective models
With MD disk attached,the inner diameter will be 35mm

DB740-0For 42mm objective models
With MD disk attached,the inner diameter will be 30 mm

The March Flip Caps can be locked in a fully open position. Having the caps lay flat against the scope body prevents breakage and gives the shooter a better view of the target area from over the scope.

FC-41for Eyepiece

FC-46for Wide Angle Eyepiece

FC-33for 24mm objective models

FC-51for 42mm objective models

FC-60for 52mm objective models

FC-64for 56mm objective models

March offers optional Leather Caps that not only protect your valuable new scope but also provides a traditional look to a modern piece of optical art. This comes with caps for both objective and ocular lenses.

LC-24for 24mm objective models :
D10V24, D10V24M,D10V24T, D10V24TM, D10V24TI,D8V24FML,D8V24FIML

LC-42

for 42mm objective models :
D25V42, D25V42M, D25V42T, D25V42TM, D25V42TI, D24V42FML, D24V42FIML,D24V42FMA,D24V42FIML

LC-52

for 52mm objective models :
D40F52, D50F52, D60F52, D32V52L, D32V52LM, D32V52T, D32V52TM, D32V52TI, D60V52L, D60V52LM, D60V52T,D60V52TM, D60V52TI
*This does not fit the eyepiece of D28HV52WFIML, D28HV52WFML

LC-56

for 56mm objective models :
D50V56T, D50V56TM, D50V56TI, D60HV56TI, D60HV56T, D60HV56TM, D60HV56L, D60HV56LM, D80V56T, D80V56TM, D80V56TI, D40V56FML(G2), D40V56FIML(G2), D40V56FML10(G2), D40V56FIML10(G2),D40V56FMA4, D40V56FMA8(G2), D40V56FIMA4, D40V56FIMA8(G2), D60V56GFIML, D60V56GFIML10, D60V56GFIMA, D60V56GFML, D60V56GFML10, D60V56GFMA
*This does not fit the eyepiece of D42HV56WFIML

LC-56W

for wide angle 56mm objective models :
D42HV56WFIML, D42HV56WFIMA, D80HV56WTIX-GR, D80HV56WTIMLX-GR

Ultra low illumination is a very dark 4 level illumination module invisible to your naked eye. If you attach a night vision on the ocular side, even the darkest settings in the 6 level illumination are too bright. Therefore, we developed an ultra low illumination module to accommodate to the night vision on the ocular side.
Dark settings, level “1” or “2” in the 6 level illumination module will be adequate for usage of night vision attached on the objective bell as you will be seeing the image of the night vision through the scope. For a night vision attached on the objective bell, you do not need to use an ultra low illumination module.
*All our illumination modules are interchangeable.

Thermal vision devices can differentiate varied levels of infrared light energy emitting from the target as heat. With standard Nightvision devices, adding an infrared illuminator that is installed on the gun can give extra illumination of the target without spooking the intended game or predator target. If the device is mounted behind the eyepiece, then the Ultra Low Power illumination module will allow the user to set the brightness to a level that will work properly with Nightvision / Thermal Vision and added Infrared Light devices, without it being too bright when compared to the target image being seen through the device.

DA233-UL

The Six Level Illumination Switch produces six levels of light intensity on the reticle. This feature is useful for precision shooting in low light or night conditions. Rotating the knurled dial doubles the intensity with each increasing level. The rubber switch turns illumination on or off while maintaining the user-selected intensity level. After one hour, illumination will automatically shut off to save battery life.

Thermal vision devices can differentiate varied levels of infrared light energy emitting from the target as heat. With standard Nightvision devices, adding an infrared illuminator that is installed on the gun can give extra illumination of the target without spooking the intended game or predator target. The March 6 level illumination module is designed to work with Nightvision, Thermal Vision with or without additional Infrared Light illumination of the target when the Nightvision or Thermal Vision device is mounted in front of the objective lens.

DA656-0

To help with fine or rapid focus changes at different distances, March scopes can be upgraded using a 49mm diameter Middle Focus Wheel. It will assist making quick and fine adjustments easier with the focus knob.

2-DB340-0

(Discontinued)for Fixed power 48×52, 40-60×52 EP Zoom,
non-illuminated models of 10x-60×52 (D60V52L & D60V52LM & D60V52T & D60V52TM)
(inner diameter 31mm)
*Applicable for orders we received before November 2022. After that the parts number will be 2-DB341-0.

2-DB341-0

for non-illuminated models of
1x-4.5x, 1x-10x, 2.5x-25x, 5x-50x, 8x-80x, 1x-8x, 3x-24x, 5x-40x, 10x-60×56, 4.5-28×52, 6-60×56, 48×52, 40-60×52 EP zoom, 10-60×52
(inner diameter 34mm)

2-DB342-0

for illuminated models of
1x-4.5x, 1x-10x, 2.5x-25x, 5x-50x, 8x-80x, 1x-8x, 3x-24x, 5x-40x, 10-60×52, 10x-60×56, 4.5-28×52, 4-40×52, 6-60×56
for non illuminated model of
5-42z56 Genll(inner diameter 36mm)

2-DB729-0

for 5-42×56, 5-42x56Genll, 8-80×56 Majesta illuminated models (inner diameter 39mm)

Shooting at very close ranges often requires very fine adjustment of the focus dial. March has produced a Large Wheel to fit over the Middle Focus wheel to enhance the dial’s ability to focus clearly. A great addition to Air Rifle Field Target and other shooting disciplines requiring accuracy. Large wheel can’t be used alone as it is put on a middle wheel. There are 2 sizes available.
Please click HERE to see how to install a large wheel.

2-DB343-0 (3.5inch / 8.89cm)

2-DB402-0 (4.5inch / 11.4cm)

March offers two blank dials for shooters to create their own Ballistic Drop Compensator (BDC). These blank BDCs replace the existing elevation knob on your March scope and let you create your own elevation adjustments to suit your load. Make any changes to your load and replace the tape on the dial quickly and easily. The blank dials can also be used for air rifle field events in conjunction with the Large Wheel for added accuracy at short ranges.
Please click HERE to see how to install a large dial.

DB392-0 (the shorter dial)for 1x-4.5x, 1x-10x, 1.5-15x, 2.5x-25x, 1x-8x, 3x-24x, 5x-40x with tactical turrets

DB393-0 (the taller dial)for 10x-60x, 5x-50x, 8x-80x with tactical turrets

This Windage Dial reverses the standard dial on the scope so that now with this turret left wind is on the left and right wind is on the right, allowing shooters to instinctively cope with quick wind changes. There are engraving on both sides. Right:1-9, Left:1-9

DB209-HFor Tactical type of 10x-60x, 5x-50x, and 8x-80x

DB046-BFor Normal type of D40F52, D50F52, D60F52, D36V52E, D32V52L, D32V52LM, D48F52, D60V52L, D60V52LM, D60HV56L, D60HV56LM

The Fast Lever helps move the zoom ring quickly and easily without the need to shift or head positions. Ideal for rapid fire disciplines on targets at multiple ranges. March fast lever is made of plastic which the engineers at March actually put a lot of thought into. As this is not made of metal, March fast lever will not damage your scope. Also it comes off easily when it is caught in branches but when used normally, it is firmly mounted and will not come off.

DA411-BBlack

DA411-CClear

Use the Smart Phone Adapter to take photos through your March Rifle Scope. The adapter can be adjusted to suit most current Smart Phones. This can be used for all March scopes. However you would need additional parts for 48×52, 40-60×52, 4-40×52, 6-60×56, 4.5-28×52 and 5-42×56.
For 4.5-28×52 & 5-42×56 WideAngle you need additional 2 parts
and for 48×52, 40-60×52,4-40×52 & 6-60×56 Genesis you need additional 1 part.
Do not use while shooting for your safety.
Please click HERE to see the installation instructions.

DA367-0Smart Phone Adapter

DB464-0Connecting bell(short)

   for 48×52, 40-60×52,4-40×52 & 6-60×56 Genesis, 4.5-28×52 & 5-42×56 WideAngle

DB684-0Adapter ring for 4.5-28×52 & 5-42×56 WideAngle

Strong and reliable perfectly fitted mounts by Area 419. They are produced to the exact tolerances of March Scopes. Self aligning rods to hold the ring top in place, never worry about your scope moving whilst undergoing the mounting process!
*The rings/mounts are supplied by March Scopes UK/Europe and not by DEON. DEON only distributes Hunt rings to customers in Japan. Please contact March UK/Europe for inquiries. Their email address is info@marchscopes.co.uk. Please check this link for further information. https://www.marchscopes.co.uk/march-scope-rings-by-area-419/

• HUNT Rings: Light and super rigid 2 piece scopes rings. Like most rings, these begin as separate parts. We are making the bases and caps in batches. While many will make these parts, send them to anodize, and then just assemble, we produce around the extra steps. Once these parts return from anodize, they are fully assembled, placed back into specially produced rail fixtures, with the caps torqued to spec over specially made spacers (to give the rings space to torque down on the optic), and final-bored as sets in our world-class machining centers. Rings are then brought off the machine in sets, and packaged together so you know that your rings were made for one another, and you can rely on them for decades.
SPECS
-Material: 7075 Aerospace Grade Billet Aluminum (with Stainless Steel Hardware)
-Coating: Type 3 Hardcoat Anodize (internal bore is raw aluminum)
* DEON only distributes specific models of Hunt rings to customers in Japan.

• MATCH rings:
THE ultimate 2 piece scope rings. Like most rings, these begin as separate parts. We are making the bases and caps in batches. While many will make these parts, send them to anodize, and then just assemble, we produce around the extra steps. Once these parts return from anodize, they are fully assembled, placed back into specially produced rail fixtures, with the caps torqued to spec over specially made spacers (to give the rings space to torque down on the optic), and final-bored as sets in our world-class machining centers. Rings are then brought off the machine in sets, and placed into the laser to mark them as sets, with each set being uniquely identified as a match to its precision-bored counterparts.
SPECS
-Material: 7075 Aerospace Grade Billet Aluminum (with Stainless Steel Hardware)
-Coating: Type 3 Hardcoat Anodize (internal bore is raw aluminum)

Strong and reliable perfectly formed Tactical One-Piece Scope mount. Like most mounts, these begin as separate parts. We are making the bases and caps in batches. While many will make these parts, send them to anodize, and then just assemble, we produce around the extra steps. Once these parts return from anodize, they are fully assembled, placed back into specially produced rail fixtures, with the caps torqued to spec over specially made spacers (to give the rings space to torque down on the optic), and final-bored as sets in our world-class machining centers. Mounts are then brought off the machine in sets, QC’d and packaged, ensuring that you receive a mount that was finished perfectly.
KEY FEATURES
-CNC Milled in America from American 7075 Aluminum
-Raw aluminum, precision bored scope contact surfaces for maximum grip
-Final-bored in sets, and never fully disassembled after boring
-Multiple accessory mounting points
-Separate rail clamping bars for maximum grab on the pic rail
-Inset clamping feet, allowing for maximum mounting adjustment and pic rail utility
-Steel guide pins between base and caps, aiding in alignment
-Custom nitrided stainless hardware
-Patent-Pending ultra-rigid and repeatable top accessory attachment

The Eyepiece extension ring included in the kit extends the eyepiece so you can use it with your eye attached to the eyepiece. As it is covered with rubber, you can look into it like a binocular or a spotting scope. The difference with a spotting scope is that you can use the same rifle scope (same model, same reticle) as the shooter.
Scope is attachable with a mount ring corresponding to picatinny rail. Includes tripod screws attachable to tripod on the market. By zooming, you can achieve a wide view (at lower magnification) and also cofirm the point of impact (at higher magnfication). The reticle of the rifle scope will aid to correct the point of impact. Middle wheel will assist you in making a fine adjustment of the side focus.

Please click HERE to see the installation instructions for spotting scope accessories.

The Spotting Scope Accessories kit includes the following ;
• Tripod adapter with screws
• Middle focus wheel 34mm(for non-illuminated models of 1x-4.5x, 1x-10x, 2.5x-25x, 5x-50x, 8x-80x, 1x-8x, 3x-24x, 5x-40x, 10x-60×56, 4.5-28×52, 6-60×56), 36mm(for illuminated models of 1x-4.5x, 1x-10x, 2.5x-25x, 5x-50x, 8x-80x, 1x-8x, 3x-24x, 5x-40x, 10x-60×56, 4.5-28×52, 4-40×52, 6-60×56), 39mm(for wide angle illuminated model of 5-42×56)
• Allen wrench
• Eyepiece extension ring
• Conversion ring : This conversion ring will enable the eyepiece extension ring to attach to a wide angle(5-42×56 and 4.5-28×52) eyepiece of the new models.

DA678-0

This Eyepiece rubber can easily be attached to any eyepiece except for wide angle series 5-42×56 and 4.5-28×52.

DB499-0

These are replacement rubbers which are to protect the moving part of the scope from dust. When the rubber is damaged, you can easily replace them by hand.

DB510-0 for 6-60×56 Genesis front

DB511-0 for 6-60×56 Genesis rear

DB644-0 for 4-40×52 Genesis front

DB644-0 for 4-40×52 Genesis rear

Tenebraex lens covers & custom-made adapter rings by DEON
This is a custom-made set specially designed for the 5–42 Gen II model, created in response to the shooters’ request. It is suitable for PRS and long-range shooting. This set includes 2 adapter rings and 2 lens covers for both ocular and objective sides. Covers are made by Tenebraex and the adapater rings are made by DEON in Japan.

Scope cover made in Japan designed by DEON features a water-repellent finish that protects the scope from rain, scratches, and dust. The scope cover is available in two versions: with detachable side flaps on both sides, or without flaps. The flapped version helps shield the firearm’s action area from direct sunlight, reducing heat buildup and minimizing its impact on shooting performance. Removable flaps are equipped with a small accessory storage pocket. This item can be machine washed; however, we recommend placing it in a laundry net.

SCLWF Scope cover Long 500mm with flaps

SCMWF Scope cover Medium 440mm with flaps

SCL Scope cover Long 500mm without flaps

SCM Scope cover Medium 440mm without flaps

Designed by DEON and made in Japan, this gray hat features clean and simple styling. Its full mesh construction provides breathability, keeping you cool and comfortable even when you sweat. A Velcro-adjustable strap at the back allows for an easy, customizable fit.